A spray-on bed liner is one of the lowest-maintenance upgrades you can put on a truck. It doesn’t need waxing, it won’t shift around, and it shrugs off the kind of abuse that would wreck bare paint.
Low maintenance isn’t the same as no maintenance, though. A few minutes of care every so often keeps your liner looking sharp, keeps the textured surface doing its job, and helps your truck hold its value when it’s time to sell. Here’s how to do it right.
The Short Version
If you only read one section, read this one:
- Rinse loose dirt out with a hose.
- Scrub with mild soap and a stiff nylon brush.
- Rinse well and let it air dry.
- Spot-clean grease or oil with a degreaser as soon as you notice it.
- Skip slick, silicone-based dressings. They make the bed slippery.
That’s it for most trucks. The rest of this guide covers the details and the less common problems.
Why a Clean Liner Matters
That textured finish is great for grip, but it’s also great at holding onto dirt, sand, mud and grime. Left alone, grit gets ground into the surface every time cargo slides across it, which wears the texture down faster and dulls the color.
Keeping it clean also makes it easier to spot problems early, like a deep gouge from a dropped tool or an edge that’s taken a hit.
How to Wash a Spray-On Bed Liner
You don’t need anything special. A garden hose, a bucket, a stiff brush and a mild soap will handle almost every job.
1. Rinse first. Spray out loose dirt, leaves and gravel before you start scrubbing. If you scrub dry grit into the liner, you’re basically sanding it.
2. Use a mild soap. Regular car wash soap or a little dish soap in a bucket of water works well. You don’t need anything stronger for normal dirt.
3. Scrub with a stiff nylon brush. A soft sponge won’t reach down into the texture. A stiff nylon brush will. Avoid wire brushes, which can scratch and tear the surface.
4. Rinse thoroughly. Soap left in the texture attracts dirt, so rinse until the water runs clear. Don’t forget the corners, the wheel wells and the tailgate.
5. Let it air dry. Leaving the tailgate down helps water drain out.
How often? For most people, whenever you wash the truck is plenty. If you haul mulch, dirt, feed or anything messy, give the bed a quick rinse after each load.
Can You Pressure Wash a Bed Liner?
Yes, and it’s one of the easiest ways to get mud out of the texture. Just use a little common sense:
- Keep the nozzle at least a foot away from the surface.
- Use a wide fan tip, not a pinpoint tip.
- Keep the spray moving instead of holding it on one spot.
- Go easy around the edges where the liner meets the paint.
Removing Grease, Oil and Tough Stains
Truck beds see a lot of things that don’t belong on a clean surface: motor oil, hydraulic fluid, grease from a hitch, tree sap, paint. A few tips:
- Clean it up quickly. The longer something sits, especially in the sun, the harder it is to get out.
- Use a degreaser for oil and grease. Spray it on, give it a minute to work, scrub with your nylon brush, and rinse well.
- Test anything stronger first. If you’re trying a solvent for paint or sap, try it on a small, hidden spot first and rinse it off right away.
- Avoid harsh chemicals as an everyday cleaner. Strong solvents aren’t necessary for regular washing and aren’t worth the risk.
Fading and Sun Exposure
If your truck sits outside, you may notice a standard liner slowly turning from deep black to a duller gray over the years. That’s normal for many bed liners. It’s caused by UV rays from the sun, not by the liner breaking down.
A few ways to deal with it:
- Prevent it. A tonneau cover or bed cap keeps the sun off the liner and protects your cargo too. Read why truck bed covers are a smart choice.
- Restore it. A water-based trim or bed liner restorer can bring back some of the original color. Apply it to a clean, dry liner and wipe off any excess.
- Choose UV+ from the start. If you want a liner that holds its color, Patriot Liner UV+ adds UV resistance that helps prevent fading in the first place. Ask your local dealer if they offer it.
One important warning: avoid silicone-based tire shines and protectants on the floor of the bed. They look great for a day, but they make the surface slick, which defeats the whole purpose of a textured liner and can be dangerous when you’re climbing in and out.
Smart Hauling Habits
The way you load the bed matters more than how often you wash it.
- Don’t drag heavy, sharp items. Lift steel, concrete blocks and equipment with sharp corners rather than sliding them across the floor.
- Strap down your load. Cargo that bounces around for 50 miles does more damage than cargo that stays put.
- Protect the tailgate edge. It takes the most abuse every time you load and unload. A tailgate cap or a moving blanket helps.
- Watch for heat. Don’t set anything hot, like a running small engine or a fresh weld, directly on the liner.
What to Do If Your Liner Gets Damaged
Spray-on liners are tough, but a dropped engine block or a sharp piece of steel can still leave a gouge. The good news is that spray-on liners can usually be repaired. In most cases, a dealer can patch the damaged area and blend it in so well that you’d have a hard time finding it.
If you notice any peeling, bubbling, flaking or cracking, contact your local Patriot Liner dealer. Those issues are covered under the Nationwide Limited Lifetime Warranty for as long as you own your truck. Read more about what the warranty covers.
Seasonal Tips
Winter: If you drive on salted roads, rinse the bed and the underside of the truck regularly. Salt sitting on exposed metal is one of the fastest ways to start rust. Our guide to preventing rust in your truck bed goes deeper on this.
Summer: Clean off bird droppings, tree sap and bug splatter quickly, since heat bakes them in. A bed cover helps a lot here too.
Hunting season and farm work: Rinse out blood, feed, manure and fertilizer as soon as you can. They stain and they smell.
Frequently Asked Questions
What’s the best way to clean a spray-on bed liner? Rinse it, scrub it with mild soap and a stiff nylon brush, rinse it again and let it dry. That handles almost everything.
Can I use a pressure washer on my bed liner? Yes. Keep the nozzle at least a foot away, use a wide fan tip and keep it moving.
What should I avoid using on a bed liner? Wire brushes, harsh solvents as an everyday cleaner, and silicone-based shine products that leave the surface slippery.
How do I make a faded bed liner black again? A water-based trim or bed liner restorer can bring back some of the color. For long-term color, ask your dealer about Patriot Liner UV+.
Can scratches in a spray-on liner be fixed? Usually, yes. Light scuffs blend into the texture on their own. Deeper gouges can be patched by your dealer.
Should I put a bed mat over a spray-on liner? You don’t need one. A spray-on liner already gives you grip and protection. If you want extra cushioning for fragile cargo, a mat is fine, but lift it out and rinse underneath now and then so dirt and water don’t sit under it.
How long does a spray-on bed liner last? With basic care, a quality spray-on liner should last as long as you own the truck. That’s why Patriot Liner backs every install with a Nationwide Limited Lifetime Warranty.
More questions? Read the full Patriot Liner FAQ.
Need a repair or have a warranty question? Find your local Patriot Liner dealer.